How To Set Time On Talking Atomic Watch
Atomic Lookout
Setting instructions for virtually common ones
AFTER YOU FOLLOW THE INSTRUCTIONS Beneath:
If you require any technical help, delight contact:
Independent Living Aids
Telephone: (800) 537-2118
Electronic mail:
techsupport@independentliving.com
Independent Living Aids
ILA Item: 756504
TALKING ATOMIC WATCH INSTRUCTIONS
Your Analog Talking Picket is a Multi-Band Radio Controlled sentinel. The National Constitute of Standards and Applied science (NIST) radio station, WWVB, located in Ft. Collins, Colorado, continuously broadcasts the time signal at 60 KHz. This signal can exist received up to 2,000 miles abroad, anywhere in the continental United states of america where long wave (AM) radio reception is possible. The WWVB station derives its signal from the NIST Diminutive Clock in Bedrock, CO. Your Diminutive Watch automatically adjusts for daylight saving fourth dimension.
BEFORE YOUR Commencement TIME USING Information technology, SET YOUR TIME ZONE!
AFTER YOU Accept SET YOUR Fourth dimension ZONE FOR THE First TIME, Please wait WHILE the clock hands are automatically spinning. The watch is setting the right time. Your picket volition resume running with the correct time automatically when the second hand stops spinning fast. Yous will non be able to use whatsoever other function while the watch is setting itself. THE Time FRAME THAT THIS MIGHT TAKE Tin can NOT BE CONSISTENTLY DETERMINED. This process could accept as long every bit 20 minutes, but depending on your location in the United States, it could exist either shorter or longer.
Time Zone Setting:
To receive the correct time you first need to set your Time Zone:
Hold THE BUTTON POSITIONED AT 8 o'clock for more than v seconds until the watch says "Prepare Alarm, Press THE ten o'clock button to set"
Button THE push button at the 8:00 position, some other three times in a row, until the watch says "Time Zone Setting. Press THE button at the x o'clock position, to set"
Press THE button at the 10 o'clock position, one time
Subsequently you press the button at the 10 o'clock position, the watch will say "Press two o'clock button to set, 8 o'clock button to confirm"
Press the 2 o'clock push repeatedly until you reach the correct fourth dimension zone then you will hear it say:
Press the 8 o'clock button to ostend after making your selection
After confirmation, the lookout hands will spin automatically until they attain the local time of the selected time zone.
When switching between "Daylight Saving Time" and "Standard Time" the time will be corrected after signal reception has been updated overnight. This usually takes identify between 2:00 AM and iv:00 AM Eastern.
The spotter will synchronize with the USA atomic clock automatically every night.
Talking Functions:
Time:
Push the 2 o'clock button to hear the Hour and Minute.
Date:
Push button the 4 o'clock push button to hear the Mean solar day, Month, Engagement, and Year
Annotation: There is no Date Talking office after a new battery is installed until it receives a signal for the first time.
Reception Status Check:
Push the viii o'clock push in one case while the watch is running normally.
if the reception was successful, the picket will say "United states Fourth dimension Updated"
if the reception failed, the watch will say "Us Time Non Updated"
Alarm Time:
Button the 10 o'clock button once and you will hear if the Alarm Time has been set
If the Alert is turned Off, the watch will say "Warning is Off"
If the Alarm Is turned On, the watch will say "The alarm time is" (followed by the alarm time)
Alarm Settings:
Set Daily Alarm Time:
Hold the 8 o'clock button while the scout is in real fourth dimension mode for more than 5 seconds until the watch says "Gear up Alarm, Press 10 o'clock button to set up."
Press the ten o'clock push button.
The watch says, "Press 2 o'clock push button to set Hour, four o'clock push button for Minutes, 8 o'clock to ostend."
Press the two o'clock button repeatedly to set 60 minutes. Adjacent printing the four o'clock repeatedly for Minute.
Press the 8 o'clock button to ostend after you accept set the Alert time.
After confirmation, the spotter will say the Alarm time that you take gear up.
You can besides check your Alert time with a push button of the 10 o'clock push button any time yous want.
The Warning is a Daily warning, and so even after you plow off the Beeping Sound, the alarm will Beep again the next day. If y'all desire to permanently turn off the Daily alarm, you tin can follow the Warning Off setting below.
Every fourth dimension the Alarm goes off, the watch will say the Alarm Time.
Alarm ON/OFF:
Concord the 8 o'clock button while the sentinel is in the real time mode for more than v seconds until the watch says "Gear up Warning, Printing ten o'clock to set."
Push the 8 o'clock button ane more time, the sentinel says "alarm ON/OFF, Press 10 o'clock push to prepare."
Press the 10 o'clock push.
The sentry says, "Press two o'clock button to plough ON, iv o'clock button to turn OFF, 8 o'clock button to confirm.
To turn ON the daily alarm, Press 2 o'clock button. To turn OFF the daily warning, Printing iv o'clock push button.
Press 8 o'clock button to confirm.
If warning is OFF, the watch says, "The alert is OFF" when 10 o'clock button is pushed.
If alarm is ON the spotter says, "The alarm time is" followed by the alarm time when x o'clock push is pushed.
Hourly Chime Settings:
Hourly Proclamation (Chime) ON/OFF
(When Chinkle is ON, the sentry announces the HOUR every Hr)
Hold the 8 o'clock push button while the scout is in the real time fashion for more than 5 seconds until the sentinel says "Set alarm, Press 10 o'clock push to set."
Push eight o'clock button 2 more times, until the spotter says "Chine ON/OFF, Press 10 o'clock button to fix."
Printing the 10 o'clock button.
The watch says, "Printing ii o'clock button to turn ON, 4 o'clock button to turn OFF, eight o'clock push button to confirm.
To turn OFF a Chinkle Alert, Press 4 o'clock push. To plow ON a Chime Alert, Press two o'clock button.
Press eight o'clock button to ostend.
Subsequently a Chime alert is turned ON, the watch will denote the Hour every one hour.
Manual Betoken Reception:
Set the correct Time Zone before initiating Manual Signal Reception. Go to "Time Zone Setting" department for details. Follow below if you want your watch to search for point immediately and not wait overnight.
Note: the below steps might require sighted help.
While the watch is in normal running style:
Press and agree the 10 o'clock button until the second hand stops at the seven o'clock position.
The watch takes most 5 to 15 minutes to pick upwards the radio signal. Wait until the watch has finished the betoken receiving process.
After successful bespeak reception, the watch will show the correct time after the fast running second-paw stops.
Push 8 o'clock push button once. The watch volition say the status of the reception.
If reception was successful, the watch will say "USA Time Updated."
If reception failed, the lookout man will say "USA Fourth dimension Not Updated."
You lot may move watch to another location where reception may be more favorable and try transmission reception over again or wait overnight for improve possible reception.
Notation: This process stops the watch from talking, and then you may seek sighted assistance during this setting phase.
Manual Fourth dimension Setting:
You should apply this part if traveling to countries with no signal reception. You must besides set correct fourth dimension of day (AM/PM) and time zone when yous come back from traveling to other countries.
hold the 8 o'clock push button for more than v seconds until the watch says "Set up Alarm, Printing 10 o'clock button to set"
Push 8 o'clock button iv more than times, until the watch says, "Set time. Printing 10 o'clock push to fix"
press 10 o'clock button
the sentinel says, "Press 2 o'clock button to set Hour, iv o'clock button for minutes, viii o'clock button to confirm"
Press 2 o'clock push button to set Hour. Listen very carefully to watch to make sure the right AM or PM has been gear up (if you set the wrong AM/PM your watch will not exist able to pick upwardly signal at 3:00AM).
Press 4 o'clock push to gear up Minute.
Press 8 o'clock button to confirm subsequently you lot take ready the Fourth dimension.
After confirmation, the watch will automatically run to the time yous have prepare. Look until the watch stops running fast.
Your watch is not able to manually set up Twenty-four hour period, Calendar month, and Yr. The watch provides this information only when a first signal reception is received.
Troubleshooting:
Your watch is a very fragile and precise instrument. Although uncommon, sometimes difficult knocks or vibrations can cause the hands to move irregularly, and therefore displays the incorrect time, although the internal clock is keeping accurate time. If when doing a "manual betoken reception" (printing and hold the 10 o'clock button until the second manus stops) the 2d-hand does not pause exactly at the 7 o'clock reference signal (half second deviation is adequate), the second-hand needs to be re-calibrated.
Re-calibrate the shifted second-hand:
Make sure the sentry is running normally.
Hold 8 o'clock button for more than than 5 seconds until the watch says "Gear up warning, Press 10 o'clock button to set."
Push 8 o'clock push button 5 more times until the watch says "2d-Hand Alignment, Press 10 o'clock to set up."
Press the ten o'clock button. Watch says, "Printing 2 o'clock button to set up, viii o'clock push to confirm."
Keep an eye on the second-mitt equally it moves to a new position and stops somewhere before six o'clock position then immediately press 2 o'clock button repeatedly until the second-mitt points exactly down at six o'clock position. Press viii o'clock button to ostend. (The spotter will terminate for a while. But await until the watch resumes normal running).
If the second hand stops advancing before it reaches six o'clock position repeat steps 2 through 5 until the second-hand points to exactly 6 o'clock.
The second hand is re-calibrated.
Annotation: This process may require obtaining sighted assistance.
Sentinel Not Receiving Time Betoken:
Reasons for not existence able to receive the Fourth dimension Signal include:
Depending on your location in the United States, if east of Colorado, you must locate a west facing window. If west of Colorado, you must locate an East facing window.
Ensure that the sentry is set up by a window, as this provides the best reception; y'all may take to try different windows in the firm to see which is all-time. Delight not that reception is e'er better at nighttime. If your watch is unable to receive the radio signal, it volition continue to function in the same way as a standard spotter. The time will and then be corrected the next fourth dimension your watch receives the time point.
Bombardment Replacement:
This watch uses a CR2025 blazon battery; trained jewelers or lookout specialists should replace the batteries to avoid damage to the watch.
Open up and carefully remove the back of the watch.
Lift up the battery spring on the right.
Remove the battery and insert a new ane with the polarity "+" facing up.
Push the battery spring down.
Earlier you supervene upon the case-back, brand sure the seal is in place.
The lookout does non run later a new bombardment is replaced until the following initiation has been done:
Set the hands and initialize the electronics.
All hands (hour, minute, and 2d-hands) have to exist moved to the 12 o'clock position (12:00:00) to initialize later on battery alter. The watch will non run until re-initialized.
Immediately after battery has been replaced concur 2 o'clock push until the hands motility quickly. You tin stop the fast movement by pressing 2 o'clock button again.
Stop the fast movement before the second-hand reaches the 12 o'clock position (11:58:00) by pressing the 2 o'clock push button.
Adjust the second- hand 1-second at a time to move it to the 12 o'clock position (12:00:00) by pressing 2 o'clock push. (If y'all accidentally become by the 12, outset this process once again.)
When all hands are aligned at the 12 o'clock position (12:00:00), PUSH ten o'clock button for 1 second to confirm.
Afterward confirmation, follow the procedure below later on the watch resumes running:
a.Set your watch to the correct Fourth dimension Zone.
b.Set your Local Time manually (get to Transmission Time Setting for details). Y'all don't need to set the exact minute and second just make certain HOUR and AM/PM are right. You watch will synchronize to the Atomic clock after it receives the point (the reason to set time is to brand sure your sentinel will initiate indicate reception at around 3AM local time.)
c.Put the lookout man in a location where reception is possible. The watch volition automatically initiate a reception at 3AM. After receiving a valid time signal, the hands volition move on the correct time.
Source: http://www.emilysfavorites.com/AtomicWatchSettingInstructions.html
0 Response to "How To Set Time On Talking Atomic Watch"
Post a Comment